Skip to content
Concept demo

A fictional brand, designed and built by Get Ranked On Top. Not a real company.

Handbuilt steel bicycles · Southeast Portland · Since 2009

Steel, drawn to the millimetre.

Touring, gravel and city frames, measured to you and fillet-brazed by two people in a former tyre shop on SE Ash Street. Eight bikes a month. No sales team, no robots, one very good surface plate.

Ridgeback Tourer · side elevationSize 56 · Signal Orange · Expedition 2×11
HA 72.0°SA 73.0°STACK 600REACH 387WHEELBASE 1,05501 · FILLET-BRAZED HEAD TUBE02 · DT 31.8 × 0.9/0.6/0.903 · HAND-FILED DROPOUT
TitleLC-01 Ridgeback Tourer, general arrangement
Dwg no.LC-RT-56
Scale1:2 · mm
DrawnM. Ferreira
RevC · 03/26
1,140frames built and numbered since 2009
0returned for a cracked joint. We keep the ledger.
12 wkfitting to collection for a full build
9 hrsof hand filing per frame, on average
Lifetimeframe warranty for the original rider

§ 01 — Configurator

Build your Ridgeback

Pick a size and watch the numbers move. Every dimension on the drawing is the real one we cut to; the fitting will refine it, usually by less than you expect.

DWG LC-RT-56 · REV CSCALE 1:2 · MM
HA 72.0°SA 73.0°STACK 600REACH 387WHEELBASE 1,055

Hover the drawing — the wheels are true, we checked.

Stack
600
Reach
387
Head ∠
72.0°
Seat ∠
73.0°
Head tube
180
Seat tube
560
Wheelbase
1,055
Trail
58
A Frame size

Seat tube centre-to-top, in centimetres. Not sure? That is what the fitting is for.

B Colour Signal Orange

House colour · included. Powder primer, wet top coat, baked twice.

C Build kit

Your Ridgeback

$4,890 USD

56 cm · Signal Orange · Expedition 2×11

Lead time 12 weeks · 12.6 kg built

$500 refundable deposit. Balance due when the frame leaves the paint booth.

Ridgeback Tourer geometry, all sizes (mm / degrees)
SizeStackReachHASAHTSTETTWBTrail
5054537271.074.01205005281,03264
5256337771.573.51405205411,03861
5458138272.073.51605405531,04458
5660038772.073.01805605661,05558
5861939272.572.52005805791,06155
6063839772.572.52206005921,07255

BB drop 72 · chainstay 450 · fork 395 a-c, 50 offset · clearance 700×48 with fenders.

§ 02 — The range

Three bikes. No more.

We could draw you a fourth. We would rather draw these three to your measurements, and keep getting them a little better every year.

LC-01

Ridgeback Tourer

Our oldest pattern and the one we would take round the world. Low trail, long chainstays, three bottle mounts and enough braze-ons to carry a kitchen.

Tyre max
700×48
Head ∠
71–72.5°
Load
40 kg rack
Frame
2.41 kg
From $2,650Ask about it

LC-02

Switchback Gravel

Built for the logging roads east of Estacada. Shorter rear end, a 1° slacker front, and clearance for 50 mm tyres with mud to spare.

Tyre max
700×50
Head ∠
70.5–71.5°
BB drop
78 mm
Frame
2.18 kg
From $2,890Ask about it

LC-03

Burnside City

Upright, quiet and slightly smug. Sloping top tube, front basket boss, internal dynamo routing and a kickstand plate brazed in, not bolted on.

Tyre max
650×55
Head ∠
70°
Gearing
Hub only
Frame
2.36 kg
From $2,390Ask about it

§ 03 — Material

Why steel, still

Not nostalgia. Physics, and a fondness for things that can be repaired by someone with a torch and an afternoon.

  • 01

    It does not wear out quietly

    Below its endurance limit, steel can take load cycles indefinitely. When it is overloaded it bends before it breaks, so you get a warning rather than a surprise.

  • 02

    It can be fixed in a small town

    Crashed in rural Montana? Any competent welder can make a steel frame rideable. We have walked customers through repairs over the phone twice, from a gas station.

  • 03

    It rides like it means it

    Thin-wall 4130 tubing, butted 0.9/0.6/0.9 mm, flexes just enough to take the chatter out of chip seal. We tune wall thickness to rider weight, not to a catalogue.

20%40%60%80%100%10³10⁴10⁵10⁶10⁷10⁸10⁹LOAD CYCLES (log)STRESS / UTSSteel · 10^3 cycles · 90% of UTSSteel · 10^4 cycles · 77% of UTSSteel · 10^5 cycles · 64% of UTSSteel · 10^6 cycles · 52% of UTSSteel · 10^7 cycles · 50% of UTSSteel · 10^8 cycles · 50% of UTSSteel · 10^9 cycles · 50% of UTSAluminium · 10^3 cycles · 86% of UTSAluminium · 10^4 cycles · 72% of UTSAluminium · 10^5 cycles · 59% of UTSAluminium · 10^6 cycles · 47% of UTSAluminium · 10^7 cycles · 38% of UTSAluminium · 10^8 cycles · 31% of UTSAluminium · 10^9 cycles · 25% of UTSEndurance limit: steel stops countingAluminium never does
Illustrative stress–life curves drawn from textbook behaviour, not our lab. A steel frame stressed below roughly half its tensile strength can, in principle, be cycled indefinitely. Aluminium has no such floor, which is why it is designed with a finite life in mind.
Stress as a percentage of ultimate tensile strength, by load cycles
CyclesSteelAluminium
10^390%86%
10^477%72%
10^564%59%
10^652%47%
10^750%38%
10^850%31%
10^950%25%

§ 04 — Workshop

Twelve weeks, six stations

Every frame passes through the same two pairs of hands and the same fixture we bought from a retiring builder in Eugene in 2011. It has opinions. So do we.

  1. Week 0

    Fitting

    Ninety minutes on the jig bike, measuring the parts of you that matter and a few that do not.

  2. Week 1

    Drawing

    We send a full-scale drawing and a spec sheet. You get two rounds of changes. Most people use one.

  3. Weeks 3–6

    Mitre & tack

    Tubes cut by hand, mitred to 0.1 mm, tacked in the fixture and checked twice before any brass flows.

  4. Week 7

    Braze

    Fillet-brazed at 870 °C, then filed smooth. Around nine hours of filing per frame. Nobody enjoys it.

  5. Weeks 8–10

    Align & paint

    Cold-set straight on a surface plate, then primer, two coats and clear, each baked.

  6. Weeks 11–12

    Build & shakedown

    Wheels built and tensioned, the bike assembled and ridden 40 km by one of us before it is yours.

§ 05 — Fitting appointment

Ninety minutes that save ten thousand kilometres

Marguerite has fitted 1,100-odd riders on the same adjustable jig. Bring the bike you ride now, the shoes you ride in, and any complaints. Especially the complaints.

  • Static and dynamic measurement on the jig bike
  • Saddle-pressure check and cleat alignment
  • A printed spec sheet you can keep, buy or not
  • $180, credited in full against any frame

90 minutes · $180, credited against any frame · Tuesday to Saturday

§ 06 — Rider stories

Where they went

We ask every customer to send one photograph and one sentence a year. These are three of the sentences.

“Nine thousand kilometres from Anchorage to Baja, and the only thing I adjusted was my opinion of aluminium.”

Distance 9,214 kmLoad 31 kgFlats 4
Priya HalvorsenRidgeback Tourer · 54 · 2023

“They asked about my left knee before they asked about my budget. The bike fits like it was measured, because it was.”

Commute 14 kmDays / yr 212
Desmond AchterbergBurnside City · 58 · 2024

“Bent the rear derailleur hanger in the Ochocos. Called the shop, Marguerite talked me through cold-setting it with a tyre lever. Finished the ride.”

Elevation 3,980 mDays 3
Luz Okonkwo-ReyesSwitchback Gravel · 52 · 2022

§ 07 — Questions

Asked often, answered plainly

Something else? Write to hello@larkspur-cycleworks.example. A human answers, usually with flux on their hands.

How long is the wait, honestly?

Twelve weeks from fitting to collection for a built Ridgeback, ten for a frameset. We build eight bikes a month and we do not take more deposits than we can honour. If we slip, you hear about it from us, not from your own calendar.

Do I have to come to Portland?

It helps, but no. Remote clients send measurements, photographs and the geometry of a bike they already like. About a third of our frames ship out of state in a crate we build to the frame.

Why not titanium or carbon?

Both are fine materials in the right hands. We have spent fifteen years getting very good at one of them, and steel suits the kind of riding our customers do: long, loaded and far from a bike shop.

Will it rust?

Not if you let it breathe. Every frame gets an internal frame-saver treatment and drain holes in the bottom bracket. Re-treat every couple of years and it will outlast you.

What does the lifetime warranty actually cover?

Workmanship and materials for the original owner, forever. Crash damage is not covered, but crash repair is: we will re-tube or re-braze at cost and repaint at a discount.

Can I bring my own parts?

Yes. Order the frameset and we will build it up with your components for a flat $420, including new cables, bar tape and a shakedown ride.